2902451 (1) - 01/2009Installation & Operating ManualSingle stage operation oil burners CODE MODEL TYPE3726312 F10 WITH HYDRAULIC JACK 263T3726
F10 - 8ELECTRODE SETTINGTURBULATOR SETTINGA) Loosen NUT (1), then turn SCREW (2)until the INDEX MARKER (3) is aligned withthe correct index number as
F10 - 9All pump port threads are British Parallel thread design. Direct connection of NPTthreads to the pump will damage the pump body. Riello manome
F10 - 10A) The burner is shipped with the pump set to operate on a two line system. Suctionand return lines (7 & 11 in drawing on page 8) should
F10 - 11NOTE: To protect the pump gears, it is advisable to lubricate the pump prior to purging alift system. Apply oil through the VACUUM PORT (A).S
F10 - 12BURNER SET-UP CHARTNOZZLES: Monarch R-PLP, Delavan W-B, Danfoss S-B, Steinen SS-S, Hago P.NOTE: A 60° degree nozzle is suggested, however, a
F10 - 13FOR CANADAPRECAUTIONSAIR FOR COMBUSTIONDo not install burner in room with insufficient air for combustion. Be sure there is anadequate air su
F10 - 14FOR USAPRECAUTIONSAIR FOR COMBUSTIONDo not install burner in room with insufficient air for combustion. Be sure there is anadequate air suppl
F10 - 15SPARE PARTS
F10 - 16SPARE PARTS LISTNo. DESCRIPTIONCODE SPARE PARTSNo. DESCRIPTION1 3006911 Hydraulic Jack2 3006912 Capillary Tube3 3000879 Hydraulic Air Shutter
F10 - 17BURNER START- UP FORM *35 Pond Park Rd.Hingham, MA 02043Phone: 781-749-8292Toll Free: 800-992-7637Fax: 781-740-20692165 Meadowpine Blvd.Missi
F10 - IPARTS LISTYour Riello 40 F10 burner should include the following parts. Please check to makesure all parts are present before beginning the ins
Technical Support Hotline1-800-4-RIELLO1-800-474-355635 Pond Park RoadHingham, MA 02043Phone 781-749-8292Toll Free 800-992-7637Fax 781-740-2069www.rie
F10 - 1RIELLO 40 F10TECHNICAL DATADIMENSIONSE1: 10 inch long (254 mm) tubes also available.SPECIFICATIONSFUEL: No. 2 Fuel OilFIRING RATE: 1.45 to 2.9
F10 - 2RIELLO 40 SERIESOIL BURNERCOMPONENT IDENTIFICATIONF10 BURNER COMPONENTS1. Lockout indicator lamp and 10. Air adjustment fixing screwsReset but
F10 - 3ASSEMBLY OF AIR TUBETO BURNER CHASSISThe air tube and drawer assembly are shipped in a carton separate from the burnerchassis. Choose the prop
F10 - 4B) Position the MOUNTING GASKET (3) between the flat surface of the UNIVERSALMOUNTING FLANGE (10) and the appliance. Line up the holes in the
F10 - 5METHOD 2 - SEMI-FLANGE COLLARA) Follow item C from METHOD 1.B) Align the air tube and attached adjustable collar so air tube is centered in t
F10 - 6The burner may be controlled using either a DIRECT LINE VOLTAGE control circuit(120V AC 60 cycle) OR a LOW VOLTAGE control (24V AC 60 cycle) u
F10 - 7NOZZLE PLACEMENTA) Determine the proper firing ratefor the boiler or furnace unit, consid-ering the specific application, thenuse the Burner S
Kommentare zu diesen Handbüchern